POSTHARVEST & MARKET · HARVEST
Harvest Guide
Timing, maturity, tools, handling standards and grading dimensions
Harvest sets the ceiling for everything that follows. This page breaks harvest into executable actions: when to cut, at what stage, with which tools, how to grade, and what to record. Exact maturity stages and grade thresholds depend on the target market and local trials, so this site does not present them as fixed standards.
On this page
Harvest timing: the daily window
Cut flowers are best harvested when temperature is low and transpiration is limited. Most production systems use early morning as the main window and finish postharvest handling before heat builds; late-afternoon harvest is also workable but must leave enough time for precooling and cold storage.
- Avoid harvesting while dew is still on the crop: wet flower heads and wounds favour pathogens, especially Botrytis.
- Avoid the hottest hours and rain; after rain, wait until flower heads are dry and standing water has cleared.
- Moderate pre-harvest water reduction can stabilise tissue water status, but plants should not be visibly wilted.pending
- Confirm that any applied pesticide is past its pre-harvest interval. Intervals follow the product label and local law; values from other regions or crops must not be reused.
Maturity: reading opening stage by flower form
Cut flowers are not harvested fully open: they are cut at a stage that continues to open through transport and retail and peaks in the consumer’s hands. The reference is flower structure and opening progress, not a universal day count. The table gives general observational logic; opening percentages and vase life for specific cultivars still require local trials.
| Flower form | Examples | Maturity reference | What to check |
|---|---|---|---|
| Bud type | Tulip, hyacinth | Firm bud, colouring up to first opening | Too early fails to open; too late risks petal damage in transit |
| Half-open type | Rose, gerbera, lisianthus | Outer petals unfolded, centre not fully open | Check outer petal reflexing and whether the centre is still firm |
| Spike or raceme | Gladiolus, snapdragon, delphinium | Lower florets open, upper buds plump | Judge by the whole spike, not a single floret |
| Composite head | Chrysanthemum, sunflower | Ray florets open, disc not yet shedding pollen or overmature | For sunflower, check pollen and disc condition closely |
| Filler flowers | Gypsophila and similar | Florets at first to half open, stems still firm | Avoid overmature branches that shatter easily |
| Foliage | Foliage and branch lines | Leaves mature with stable colour, not over-lignified | Check leaf undersides for pests and lesions; foliage affects vase life too |
The table lists general observational dimensions, not cultivar-specific harvest standards. Opening stage should be balanced with transport distance and sales cycle, and the same cultivar may be cut at different stages by season.
Tools and hygiene
- Use sharp, clean pruners or knives so cuts are clean; crushed stems impair water uptake.
- Disinfect tools between batches to avoid transmitting pathogens through cuts; use registered products and follow local labels for type and concentration.
- Keep harvest containers clean, free of old flowers and standing water; container walls should not press on flower heads.
- Wear gloves and minimise handling of flower heads, especially petals prone to bruising.
Harvest handling standard
- 1
Cut
Cut on an angle above a node or at the position the cultivar requires, leaving enough stem for later grading and vase use; exact height follows the cultivar and harvest plan.
- 2
Hydrate immediately
Get stem bases into clean water or a hydrating container as soon as possible; never stack cut stems in the sun.
- 3
Avoid compression
Lay flower heads in one direction in shallow layers; deep stacking causes irreversible creases and bruising.
- 4
Field holding
Hold in shade with airflow and move to precooling quickly; longer field holding makes vase life harder to guarantee.
- 5
Batch identity
Attach a batch card to each harvest crate recording cultivar, block, date and harvester to support grading and traceability.
Grading dimensions
Grading keeps a consignment consistent in length, opening stage and appearance, reducing disputes in trade. Markets differ in grade names and limits — the US, for example, has USDA AMS cut-flower references, while other markets follow their own standards or buyer specifications. This site does not treat one market’s thresholds as universal.
| Dimension | What to observe | Common practice |
|---|---|---|
| Stem length | Usable length from cut to flower head | Bundle in fixed length bands with uniform length per bunch |
| Flower head | Diameter, opening stage, petal integrity, colour | Remove deformed, faded or mechanically damaged heads |
| Stem | Thickness, firmness, straightness, node position | Reject bent-neck, hollow and broken stems |
| Foliage | Lesions, pests, yellowing, tears | Keep or strip lower leaves per buyer requirement |
| Consistency | Variation in head size, colour and opening within a lot | Split lots when variation is large; do not mix grades |
| Pests and diseases | Visible insects, feeding holes, mould, soft rot | Isolate and re-check the lot; do not hide problems by selection |
Grade names, length bands and allowed defects are set by markets and buyers; this site gives no universal thresholds. Export must follow the destination country’s official requirements and contract terms.
Harvest records and batches
Harvest records are the only link between field management and postharvest quality. At minimum record cultivar, block or batch number, date and time window, harvester, approximate quantity, weather and field condition, and where the lot went next. When a quality complaint arrives, traceability only works if the batch can be located within hours.
- Build batch numbers from block, cultivar code and date rather than a simple sequence that can repeat.
- Keep pesticide records in the same batch file as harvest dates so pre-harvest intervals can be checked.
- The local Farm Tools section can hold batches and field records, stored only in this browser and never uploaded.
Related crops
Related pages
Next
Flower Processing
Fresh-cut handling, dried flowers, deep processing and edible products
Next
Packing & Storage
Fresh and dried packing, gift boxes and labels, storage conditions, cold-chain equipment, losses and traceability
Next
Channels & Trade
Domestic channels, international trade flow, cost structures and official verification routes
Next
Material Safety
Identity, material safety, contaminant testing, food and drug law, and manufacturing licences
Sources
These public references were used for principles, workflows and regulatory frameworks. Specific values, fees and official application requirements must be checked with the competent authority where you operate.
- To be verified
《中国农业百科全书 · 观赏园艺卷》
Production practice, harvest and postharvest basics
- postharvest.ucdavis.edu
UC Davis Postharvest Technology Center
Cut-flower postharvest physiology, precooling, storage and ethylene management
- www.ams.usda.gov
USDA Agricultural Marketing Service(AMS)
US grading, market news and purchasing specifications for floriculture and horticulture
- www.fao.org
Food and Agriculture Organization of the United Nations(FAO)
General principles for postharvest handling, cold chain and loss reduction
- extension.psu.edu
Penn State Extension · Floriculture
Greenhouse floriculture, postharvest handling and grading practice
Last compiled:2026-11-15
The channel section describes channel structure and verification routes only. It lists no buyer names, prices or contact details; official pages, contact desks and directories that could not be verified are marked “to be verified”.
Content is for reference only and is not purchasing advice, processing instruction, a food-safety conclusion or legal advice. Food, drug, cosmetic-ingredient and phytosanitary matters must follow the current requirements of the competent authority in the relevant country or region.