POSTHARVEST & MARKET · PROCESSING
Flower Processing
Fresh-cut handling, dried flowers, deep processing and edible products
Processing turns a crop into a product. Fresh-cut flowers rely on process sequence to protect vase life, dried flowers depend on the drying method for form and colour, and deep processing moves into cosmetic-ingredient, craft or food regulation. The three require different operating rules and cannot share one protocol.
On this page
Fresh-cut handling sequence
The core of cut-flower handling is cooling fast, keeping water moving and limiting damage. Sequence matters more than any single step: strip lower foliage, grade, precool quickly, then pack and move to cold storage. Packing warm flowers traps field heat, and later cooling cannot fully recover it.
- 1
Strip leaves and thorns
Remove lower leaves and thorns so foliage does not sit in water and rot; retained leaves stay above the water line. How much to strip depends on vase and transport requirements.
- 2
Grade and bunch
Bunch by stem length, head condition and uniformity, removing damaged stems. Grade before precooling to avoid rehandling chilled flowers.
- 3
Preservative treatmentpending
Use postharvest preservatives according to the label for duration and concentration. Cultivars respond differently to sugars, biocides and ethylene, so trial small batches first.
- 4
Precoolingpending
Remove field heat quickly. Choose room, forced-air or vacuum cooling according to flower tolerance and pack format; temperature and duration depend on cultivar and facility.
- 5
Packing
Choose dry or wet packing by transport distance; protect heads and leave space for airflow or cooling, without compression. See “Packing & Storage” for detail.
- 6
Cold storage and cold-chain handover
Hold a stable low temperature and minimise door openings. Record temperature and time at dispatch, loading and handover to form a traceable chain.
This is a general sequence, not a set of universal temperatures or durations. Cut flowers differ widely in chilling tolerance; tropical and subtropical species are usually stored warmer than temperate ones and cannot share one setting.
Water quality and holding solution
- Use clean water and wash containers at every change; microbes in water are a major cause of blocked stems and bent necks.
- Mix holding solutions per label; do not stack biocides, sugars and acids on your own, as combinations can precipitate or injure stems.
- Ethylene-sensitive flowers such as carnation and gypsophila should be kept away from ripening fruit and ageing flowers to limit exposure.
- Specific preservative ingredients, concentrations and durations must follow registered products and local law; this site gives no formulations.pending
Dried-flower methods compared
Drying aims to remove enough moisture quickly while preserving form and colour. Method choice depends on tissue water content, petal thickness, volume and equipment. Home or small-scale work often uses air drying, hanging and pressing; larger production uses forced hot air or desiccants to speed things up.
- Judge completion by feel and moisture status, not a fixed number of days; flowers sealed before fully dry will mould.
- Store dried flowers away from light, moisture and insects; separate display from storage to avoid repeated moisture uptake.
- Before any food or cosmetic use, re-evaluate drying method, environment and pest control; ornamental dried-flower practice cannot be carried over.pending
| Method | Suitable material | Strengths | Limitations | Key points |
|---|---|---|---|---|
| Air drying | Stiff-stemmed, thin-petalled species | Simple equipment, low cost | Weather-dependent and slow | Flat or hanging in a ventilated, shaded, low-humidity space |
| Hanging to dry | Spikes, strawflower, lavender and similar | Keeps stems straight and suits bunching | Heads can distort; dense bunches mould | Small bunches, spaced apart, shaded and ventilated |
| Silica-gel drying | Thick-petalled, three-dimensional forms such as rose and peony | Better shape and colour retention | Media needs regeneration; small batch size | Bury heads fully in desiccant and seal until dry |
| Forced hot air | Batch production of moderate-moisture material | Controllable cycle, scalable | Excess heat fades colour and makes petals brittle | Low temperature, even airflow, shallow layers |
| Pressing | Thin-petalled small flowers and leaves for cards and decoration | Flat form, suited to graphic use | Loses dimensionality; thick material may mould | Change blotting paper often and weight evenly |
No temperature, humidity or duration values are given: they vary widely with material, thickness and equipment and must be set by local trials. In high-mould seasons, increase ventilation and dehumidification.
Deep processing: essential oils, hydrosols and fragrance products
Essential oils and hydrosols are extracts, not products made by steeping flowers in oil. Yield, composition and quality depend heavily on source cultivar, harvest timing, extraction method and equipment; as cosmetic ingredients or household products they are also subject to ingredient inventories, labelling, manufacturing licences and safety assessment. This site describes categories only and gives no extraction parameters.
- “Natural” is not a safety claim: natural materials can sensitise, and concentrated oils carry higher risk.
- Efficacy claims such as antibacterial, soothing or sleep-promoting are regulated and need substantiation and local compliance.
- Solvents, equipment and waste handling must meet local environmental and occupational-safety requirements.
| Product route | Input and form | Main barriers | Compliance note |
|---|---|---|---|
| Essential oil | Volatile oil from distillation or expression of aromatic material | Raw-material volume, extraction equipment, compositional testing | Regulated as cosmetic ingredient or chemical; composition and safety data required |
| Hydrosol / floral water | Aqueous co-product of distillation | Microbial control, preservation, stability | Cosmetic claims require full notification and compliant labelling |
| Sachets and spice blends | Dried petals, buds and spice blends | Moisture and insect control, scent longevity | Food-contact or skin-contact uses follow the corresponding category |
| Crafts and cultural products | Dried and pressed flowers, resin encapsulation, floral gifts | Design, handcraft capacity, logistics protection | Re-assess for children’s products, food contact or fragrance claims |
Edible flower products
Candying, floral teas, pastry decoration and infused drinks are food processing and fall under food-safety law, not ornamental horticulture rules. Material must be a verified edible cultivar and plant part; cultivation must be managed as a food raw material; and postharvest handling, drying, packing and labelling must meet food requirements. The same species grown ornamentally cannot simply enter a food chain.
- Ornamental flowers are not recommended as food or medicinal material; nothing may be sold as an edible flower before identity and testing are complete.
- Pesticide use on edible flowers must meet food-raw-material registration and residue requirements; ornamental programmes cannot be reused.
| Product form | Typical plant part | Critical control points | Regulatory direction |
|---|---|---|---|
| Floral tea / dried flowers | Buds or petals | Identity, pesticide residues, drying and microbiology | Food raw material and national food-safety standards |
| Candied flowers and preserves | Petals | Sugar level, preservation, processing hygiene | Food production licence and labelling |
| Pastry decoration and salads | Fresh petals | Freshness, refrigeration, cross-contamination | Food-service and ready-to-eat hygiene requirements |
| Infused alcohol and fermented drinks | Petals, fruit | Alcohol strength, extraction conditions, microbiology | Alcohol and food production licensing |
The table describes product forms and control directions only; it is not a recipe or process. Identity, material safety and testing requirements are consolidated on the Material Safety page.
Processing premises and hygiene
- Separate ornamental material from food or cosmetic inputs; tools, containers and staff flow should not cross.
- Floors, benches and drainage should be cleanable; wash water must meet the requirements of the product category.
- Record batch numbers, input origin, processing date and destination so a batch can be recalled if needed.
- Licensing conditions and procedures for food, drugs and cosmetics follow current competent-authority rules; this site neither applies on your behalf nor promises outcomes.
Related crops
Related pages
Next
Harvest Guide
Timing, maturity, tools, handling standards and grading dimensions
Next
Packing & Storage
Fresh and dried packing, gift boxes and labels, storage conditions, cold-chain equipment, losses and traceability
Next
Channels & Trade
Domestic channels, international trade flow, cost structures and official verification routes
Next
Material Safety
Identity, material safety, contaminant testing, food and drug law, and manufacturing licences
Sources
These public references were used for principles, workflows and regulatory frameworks. Specific values, fees and official application requirements must be checked with the competent authority where you operate.
- postharvest.ucdavis.edu
UC Davis Postharvest Technology Center
Cut-flower postharvest physiology, precooling, storage and ethylene management
- www.fao.org
Food and Agriculture Organization of the United Nations(FAO)
General principles for postharvest handling, cold chain and loss reduction
- www.nhc.gov.cn
中华人民共和国国家卫生健康委员会
National food-safety standards and food-medicine substance catalogues
- www.samr.gov.cn
国家市场监督管理总局
Food production licensing, product quality and metrology rules
- www.nmpa.gov.cn
国家药品监督管理局
Drugs, cosmetic ingredients and manufacturing licensing
- www.rhs.org.uk
Royal Horticultural Society · Advice
Horticultural practice and home-scale drying and pressing methods
- To be verified
《中国农业百科全书 · 观赏园艺卷》
Production practice, harvest and postharvest basics
Last compiled:2026-11-15
The channel section describes channel structure and verification routes only. It lists no buyer names, prices or contact details; official pages, contact desks and directories that could not be verified are marked “to be verified”.
Content is for reference only and is not purchasing advice, processing instruction, a food-safety conclusion or legal advice. Food, drug, cosmetic-ingredient and phytosanitary matters must follow the current requirements of the competent authority in the relevant country or region.